Wolf DCX-1000I Spezifikationen Seite 89
- Seite / 151
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
4-4
Part
Description
Frequency Action
Lens As required
Clean the lens only when absolutely necessary.
A small amount of dust on the lens has very little
effect on picture quality.
To clean: Useasoftmicroberclothwithoutany
chemicals. Use only a high-quality coated optics
cleaning uid, which can be purchased from
most camera supply stores. Apply the coated
optics uid directly onto the microber cloth
until moistened. Wipe in a single sweep across
the surface of the lens. To avoid scratching the
lens do not scrub or rub in a circular motion.
Discard the cloth after every use. Do not
use cleaning tools treated with Ether. Do not
use cleaning solvents that contain ammonia.
Use compressed air to remove any particles
remaining on the lens.
Lamp
As required
CLEAN: Clean if absolutely necessary. Never
touch the glass surface of the lamp. Fingerprints
left on the glass will seriously degrade lamp
performance or cause “hotspots” which can
lead to an accumulation of intense heat in the
touched area and cause the lamp to shatter.
To clean: Wait until lamp is cool. Moisten a
clean,microberclothwithisopropylalcoholand
gently rub the surface of the glass in a circular
motion until clean.
1000 hrs or
sooner if required
REPLACE: Refer to 4.4 Lamp Replacement
procedure later in this section.
Covers
(External)
As required
CLEAN: Clean dust from external covers using
aclean,microberclothasrequired.
NOTE: Before cleaning the modules, it is
recommended that you install the lens cap. This
will keep dust particles from settling on the glass
surface of the lens.
Table 4.1. Maintenance Guide
Section4►Maintenance
WARNING
Proper face shield and protective gloves are required if
the lamp module is removed from the projector.
4.2 Cleaning and
Maintenance Guide
- OWNER'S MANUAL 1
- TABLE OF CONTENTS 2
- INTRODUCTION 4
- 1.3 Warranty 5
- INSTALLATION & SETUP 6
- 2.2 Installation 8
- Considerations 8
- Ambient Light 9
- Other Considerations 9
- Projector Position and 10
- Mounting 10
- Lens Type 11
- 2.3 Connecting Sources 17
- YPbPr signals 18
- DVI Digital Video 19
- Composite and S-Video 19
- Optional Inputs 19
- From WC-Pro Processor 20
- Connect a RS422 device only 21
- Separating Networks 22
- 2.6 Power Connector 23
- OPERATION 24
- Input Panel 25
- Intake and Exhaust 25
- Lamp Door 25
- Front and Rear IR Sensors 25
- 3.2 Using the Remote or 26
- Built-in Keypad 26
- Theater Master 27
- Remote Control 27
- Wired Remote 28
- Guide to Keypads 28
- Keypad Commands 28
- Section3►Operation 29
- Contrast 30
- On-Line Help 33
- Editing Text 36
- Editing Numerical Values 36
- 3.4 Using Inputs and 37
- Channels 37
- – AUTOMATIC – 38
- What Channels are 39
- 3.5 Adjusting the Image 42
- Geometry and 43
- Position Menu 43
- VIDEO OPTIONS — SUBMENU 49
- INPUT LEVELS — SUBMENU 50
- ADVANCED IMAGE SETTINGS 53
- Parameters and 56
- Advanced Controls 56
- 3.6 Adjusting System 56
- 10. Wired Keypad Protocol Any 58
- ETHERNET SETTINGS - SUBMENU 59
- 60
- System Conguration 60
- — GEOMETRY & COLOR — 60
- EDGE BLENDING — SUBMENU 61
- Color Temp Adjust 63
- BLACK EDGE BLENDING — SUBMENU 64
- CONFIGURE CHANNELS 67
- 3.7 Working with PIP or 68
- Seamless Switching 68
- PIP IMAGE SETTINGS — SUBMENU 69
- Switching 70
- How Old is My Lamp 74
- When to Replace the Lamp 74
- Information Menu 74
- 3.9 Achieving White 75
- Field Uniformity 75
- IMPORTANT 76
- 3.10 Edge Blending 78
- Black Edge Blending 81
- 3.11 Remote Control of 82
- 3.12 Error Conditions 83
- System Warnings / Errors 84
- MAINTENANCE 86
- Section4►Maintenance 87
- 4.2 Cleaning and 89
- Maintenance Guide 89
- 4.3 Replacing Remote 90
- Batteries 90
- 4.4 Lamp Replacement 90
- Lamp Door - 2 Screws 91
- WARNING 92
- 4.5 Replacing the 94
- Projection Lens 94
- SPECIFICATIONS 96
- DCX-1000i and 97
- DCX-1000FD 97
- DCX-1500i and 98
- DCX-1500FD 98
- KEYPAD REFERENCE 99
- SERIAL COMMUNICATIONS 100
- Quick Start 101
- 1. Overview 102
- Overview 102
- Understanding Message Format 102
- 2. Understanding 102
- Message Format 102
- 2.1 Basic Message 103
- Structure 103
- 2.2 Sampling Messages 104
- 2.3 What is Actually 105
- Sent in a Message 105
- 2.5 Accessing Specic 107
- Source Setups 107
- 2.6 Other Special 107
- Functions 107
- 2.7 Flow Control 109
- 3.20 BRT 112
- 3.39 DTL Detail 117
- 3.40 DTT 117
- Detail Threshold 117
- 3.41 EBB Edge Blending 117
- Black Levels 117
- 3.42 EBE 118
- Edge Blending Black 118
- Levels Select 118
- 3.43 EBL 118
- Edge Blending 118
- 3.57 GAM 122
- 3.58 GIO 122
- General Input Output 122
- 3.63 HDC 124
- DHDM Conguration 124
- 3.64 HDD 124
- DHDM Dual Link Format 124
- 3.65 HDL 125
- DHDM Look Thru Setting 125
- 3.66 HISS 125
- Lamp History 125
- 3.75 KEY 128
- Key Code 128
- 3.82 LTC 130
- 3.129 ROG 138
- Red Odd Gain 138
- 3.130 ROO 138
- Red Off Offset 138
- 3.131 RTE 139
- Real Time Events 139
- 3.141 System Status 142
- 3.142 STD 142
- Video Standard 142
- THROW DISTANCE 146
- SYSTEM INTEGRATION 147
- OPTIONAL INPUT MODULES 149
- FAN BOARD 150
Verwandte Produkte und Handbücher für Projektoren Wolf DCX-1000I
Projektoren Wolf ProScaler Einstellungsanleitung
(11 Seiten)
(11 Seiten)
Projektoren Wolf DCX-1000FD Bedienungshandbuch
(152 Seiten)
(152 Seiten)
Projektoren Wolf SDC-15 Bedienungsanleitung
(10 Seiten)
(10 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern